Jump to content
  • Recently Browsing   0 members

    • No registered users viewing this page.

Aqara Hub M1S problem po próbie wgrania nowego software


flabek
 Share

Recommended Posts

Dziś aplikacja (zmodowana)wyświetliła mi monit o możliwości aktualizacji software. Dałem żeby zaktualizowało i bramka leży. Miga na biało z długimi przerwami już chyba z pół godziny. Wgranie oprogrogramowania się nie powiodło i wyświetliło "timeout". Czy uwaliłem sobie bramkę? Dać reset do ustawień fabrycznych?

Link to comment
Share on other sites

  • Developer

miales na eu sparowane? nie mam m1s eu, ale raczej bym jej nie aktualizowal dopoki nie bedzie oficjalnego wsparcia w mijia dla tego huba. moze to byl jakis losowy test na wybrane konta. oddaj po prostu na gwarancje.

  • Like 2
Link to comment
Share on other sites

U mnie w poniedziałek pojawił się monit o upgrade ale że byłem w pracy to nie robiłem. Po powrocie do domu aktualizacji juz nie było. Tez mam EU. Jedynie gdzie zrobiłem upgrade to zaraz po zakupie w Aqara Home

  • Like 1
Link to comment
Share on other sites

26 minut temu, piteron napisał:

U mnie w poniedziałek pojawił się monit o upgrade ale że byłem w pracy to nie robiłem. Po powrocie do domu aktualizacji juz nie było. Tez mam EU. Jedynie gdzie zrobiłem upgrade to zaraz po zakupie w Aqara Home

No to miałeś fuksa. U mnie wszystko leży. Najbradziej mnie wkurza to że będę musiał parować wszystkie czujniki na nowo.

Link to comment
Share on other sites

45 minut temu, flabek napisał:

No to miałeś fuksa. U mnie wszystko leży. Najbradziej mnie wkurza to że będę musiał parować wszystkie czujniki na nowo.

Czy ja wiem czy fuksa. Bardziej chyba doświadczenie. Tyle co ja sprzętów uwalilem w ten sposob to tylko @rezmus wie 😉. I tak przed aktualizacją bym sie zapytał czy bezpieczne a jak tak to co popsuli 😉

Link to comment
Share on other sites

3 hours ago, flabek said:

No to miałeś fuksa. U mnie wszystko leży. Najbradziej mnie wkurza to że będę musiał parować wszystkie czujniki na nowo.

U mnie to samo co u kolegi. Niestety zdążyłem zrobić update. Przy 100% sypło błędem i tyle w temacie. Bramkę wykrywa zmodowana mi home, mogę ją dodać ale rozłącza się z siecią wifi. Przy próbie resetu świeci zamiga zimny biały. Ktoś coś może na to znalazł sposób czy do bramka do kosza?

Link to comment
Share on other sites

2 hours ago, rezmus said:

musisz polutowac uart, zeby sprawdzic co jej nie pasuje. przez uart powinno sie tez dac naprawic. ewentualnie gwarancja.

m1s_uart_1.jpg

m1s_uart_2.jpg

Dzięki za odpowiedź. Jakieś FAQ mi hub&uart jest może na forum czy zostaje wujek google. Bez doświadczenia z uart jest wykonalna naprawa? 

Link to comment
Share on other sites

  • Developer

lutujesz jak na zdjeciach (uwaga na 220v), podpinasz adapter uart do usb, odpalasz putty i sprawdzasz loga. musze sobie pare rzeczy przypomniec, ale najprosciej bedzie zmodyfikowac mtd boot, zeby ladowal stary kernel/rootfs (hub ma 2 sloty). jak bedziesz mial podpiete to bedziemy myslec. oczywiscie tracisz gwarancje, wiec jak nie czujesz sie na silach to oddaj na serwis, bo skoro wersja eu to pewnie w pl brana.

Link to comment
Share on other sites

13 minutes ago, rezmus said:

lutujesz jak na zdjeciach (uwaga na 220v), podpinasz adapter uart do usb, odpalasz putty i sprawdzasz loga. musze sobie pare rzeczy przypomniec, ale najprosciej bedzie zmodyfikowac mtd boot, zeby ladowal stary kernel/rootfs (hub ma 2 sloty). jak bedziesz mial podpiete to bedziemy myslec. oczywiscie tracisz gwarancje, wiec jak nie czujesz sie na silach to oddaj na serwis, bo skoro wersja eu to pewnie w pl brana.

Kupiona używana bez gwarancji. W takim razie zamawiam USB/uart i myślę że przy Twojej pomocy dam radę. Dzięka😉

Link to comment
Share on other sites

W dniu 11.05.2021 o 21:22, rezmus napisał:

jakby ktos mial info to zrobcie screena, ale nie update.

Czekam aż ktoś sprawdzi to oprogramowanie. Wymienili mi huba na gwarancji, nie chcę uwalić następnej, bramka jest EU.

Screenshot_20210517-180647_Mi Home.jpg

Link to comment
Share on other sites

  • Developer
35 minut temu, flabek napisał:

Czekam aż ktoś sprawdzi to oprogramowanie. Wymienili mi huba na gwarancji, nie chcę uwalić następnej, bramka jest EU.

to nie jest m1s, tylko stary aqara hub wspierany oficjalnie w mi home. jesli chcesz to zainstaluj oryginalna apke i tam tez bedzie go widac. mozesz aktualizowac. jak padnie to wymieniaj i tyle. wina producenta. jak nie chcesz ryzykowac to nie aktualizuj nigdy. tu nie ma reguly, moze u kogos byc OK, u ciebie brick.

@Mic u ciebie tez czasem nie stara aqara? jaki model na hubie lub pudelku.

Link to comment
Share on other sites

22 minutes ago, rezmus said:

to nie jest m1s, tylko stary aqara hub wspierany oficjalnie w mi home. jesli chcesz to zainstaluj oryginalna apke i tam tez bedzie go widac. mozesz aktualizowac. jak padnie to wymieniaj i tyle. wina producenta. jak nie chcesz ryzykowac to nie aktualizuj nigdy. tu nie ma reguly, moze u kogos byc OK, u ciebie brick.

@Mic u ciebie tez czasem nie stara aqara? jaki model na hubie lub pudelku.

U mie taka wersja. Dziś przyszedł uart więc polutuje i będę pisał. Na innym forum znalazłem jak w tej wersji podpiąć pod uart.

@flabek Właśnie na tej aktualizacji udupilem bramkę...😔

IMG_20210514_191859.jpg

Link to comment
Share on other sites

  • Developer

temat byl niby o m1s, a okazuje sie, ze o aqara hub ;) jesli to stara aqara to ci nie pomoge, bo to inny soc i nie mam z nim doswiadczenia. na githubie znajdziesz info. ludzie wrzucaja tam fw oparte o openwrt i robia uniwersalna bramke zigbee. generalnie patrz na uart co mu tam nie pasuje. jest tez kanal na telegram o tej bramce, ale raczej rozmowa po rosyjsku.

https://github.com/openlumi

Link to comment
Share on other sites

1 hour ago, rezmus said:

temat byl niby o m1s, a okazuje sie, ze o aqara hub ;) jesli to stara aqara to ci nie pomoge, bo to inny soc i nie mam z nim doswiadczenia. na githubie znajdziesz info. ludzie wrzucaja tam fw oparte o openwrt i robia uniwersalna bramke zigbee. generalnie patrz na uart co mu tam nie pasuje. jest tez kanal na telegram o tej bramce, ale raczej rozmowa po rosyjsku.

https://github.com/openlumi

Te bramki to jakaś masakra... Miałem poprzednią, ale mi smart plug się z nią nie parował. Dałem do rodziców, kupiłem nowszą no i przyleciała aktualizacja która ją zepsuła. Ehh tyle sprzętów w mihome a to wszystko działa coraz gorzej z nowszym sprzętem. Poprzednia bramka lepiej działała z czujnikiem ruchu, barwy światła można było ściemniać a w tej przy przyciemnieniu barwa światła się zmienia. No nic do kosza leci bramka i zastanawiam się nad innym systemem smart home który bedzie działał 24/7. Dzięki za chęci @rezmus. Niestety nie jestem biegły w uart a tym bardziej po rosyjsku. Niby podłączyłem bramke ale jakieś krzaczki lecą w putty także chyba odpuszczam temat.

Link to comment
Share on other sites

  • Developer

podpinasz gnd do gnd, rx do tx w uart, tx do rx w uart. w putty ustawiasz serial com na ktorym masz i w ustawieniach seriala baud 115200, 8n1, flow control off.

Link to comment
Share on other sites

Posted (edited)
21 minutes ago, rezmus said:

podpinasz gnd do gnd, rx do tx w uart, tx do rx w uart. w putty ustawiasz serial com na ktorym masz i w ustawieniach seriala baud 115200, 8n1, flow control off.

Takie ustawienia mam ale pomyliłem rx-rx, tx-tx podpiąłem. To poprawie i potestuje co wypluwa bramka ale to później jak bedzie spokój w domu czyt. dziecko pójdzie spać.

putty.jpg

Edited by Mic
Link to comment
Share on other sites


U-Boot 2016.03 (Nov 07 2017 - 20:11:55 +0800)

CPU:   Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU:   Commercial temperature grade (0C to 95C) at 36C
Reset cause: POR
Board: Lumi international Gateway
I2C:   ready
DRAM:  256 MiB
NAND:  256 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment

Display: TFT43AB (480x272)
Video: [email protected] is fused, disable it
In:    serial
Out:   serial
Err:   serial
Net:   [email protected] is fused, disable it
Board Net Initialization Failed
No ethernet found.

## Enter main_loop() Now##
Normal Boot
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x300000, size 0x700000
 7340032 bytes read: OK

NAND read: device 0 offset 0xa00000, size 0x100000
 1048576 bytes read: OK
Kernel image @ 0x80800000 [ 0x000000 - 0x617290 ]
## Flattened Device Tree blob at 83000000
   Booting using the fdt blob at 0x83000000
   Using Device Tree in place at 83000000, end 8300c0e1
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
Modify /soc/[email protected]/[email protected]:status disabled
ft_system_setup for mx6
No PMIC found!

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.1.15+gb63f3f5 ([email protected]) (gcc version 5.3.0 (GCC) ) #37 SMP PREEMPT Tue Jun 19 15:28:38 CST 2018
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Freescale i.MX6 ULL 14x14 EVK Board
[    0.000000] Reserved memory: failed to allocate memory for node 'linux,cma'
[    0.000000] cma: Reserved 96 MiB at 0x8a000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 12 pages/cpu @89da3000 s16908 r8192 d24052 u49152
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttymxc0,115200 ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs cma=96M mtdparts=gpmi-nand:3m(boot),7m(kernel),1m(dtb),-(rootfs)
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 148920K/262144K available (8035K kernel code, 423K rwdata, 2812K rodata, 540K init, 426K bss, 14920K reserved, 98304K cma-reserved, 0K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0x90800000 - 0xff000000   (1768 MB)
[    0.000000]     lowmem  : 0x80000000 - 0x90000000   ( 256 MB)
[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000   (   2 MB)
[    0.000000]     modules : 0x7f000000 - 0x7fe00000   (  14 MB)
[    0.000000]       .text : 0x80008000 - 0x80aa01f8   (10849 kB)
[    0.000000]       .init : 0x80aa1000 - 0x80b28000   ( 540 kB)
[    0.000000]       .data : 0x80b28000 - 0x80b91fa0   ( 424 kB)
[    0.000000]        .bss : 0x80b94000 - 0x80bfeb5c   ( 427 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] mxc_clocksource_init 24000000
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000015] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000055] clocksource mxc_timer1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.002580] Console: colour dummy device 80x30
[    0.002620] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.002657] pid_max: default: 32768 minimum: 301
[    0.002880] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.002910] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.004274] CPU: Testing write buffer coherency: ok
[    0.004765] /cpus/[email protected] missing clock-frequency property
[    0.004808] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.004916] Setting up static identity map for 0x80008280 - 0x800082d8
[    0.041170] Brought up 1 CPUs
[    0.041209] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[    0.041228] CPU: All CPU(s) started in SVC mode.
[    0.042338] devtmpfs: initialized
[    0.064067] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.064953] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.072794] pinctrl core: initialized pinctrl subsystem
[    0.075468] NET: Registered protocol family 16
[    0.093489] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.120894] cpuidle: using governor ladder
[    0.150950] cpuidle: using governor menu
[    0.193791] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.193826] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.196990] imx6ul-pinctrl 20e0000.iomuxc: Invalid fsl,pins property in node /soc/[email protected]/[email protected]/imx6ul-evk/hoggrp-1
[    0.197691] imx6ul-pinctrl 20e0000.iomuxc: initialized IMX pinctrl driver
[    0.198382] imx6ul-pinctrl 2290000.iomuxc-snvs: initialized IMX pinctrl driver
[    0.258304] mxs-dma 1804000.dma-apbh: initialized
[    0.264967] SCSI subsystem initialized
[    0.266409] usbcore: registered new interface driver usbfs
[    0.266606] usbcore: registered new interface driver hub
[    0.266837] usbcore: registered new device driver usb
[    0.269371] i2c i2c-0: IMX I2C adapter registered
[    0.269417] i2c i2c-0: can't use DMA
[    0.270973] i2c i2c-1: IMX I2C adapter registered
[    0.271013] i2c i2c-1: can't use DMA
[    0.271315] Linux video capture interface: v2.00
[    0.271550] pps_core: LinuxPPS API ver. 1 registered
[    0.271574] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.271857] PTP clock support registered
[    0.274573] MIPI CSI2 driver module loaded
[    0.275272] Advanced Linux Sound Architecture Driver Initialized.
[    0.277430] Bluetooth: Core ver 2.20
[    0.277554] NET: Registered protocol family 31
[    0.277577] Bluetooth: HCI device and connection manager initialized
[    0.277617] Bluetooth: HCI socket layer initialized
[    0.277654] Bluetooth: L2CAP socket layer initialized
[    0.277736] Bluetooth: SCO socket layer initialized
[    0.279856] Switched to clocksource mxc_timer1
[    0.306595] NET: Registered protocol family 2
[    0.308250] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[    0.308351] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
[    0.308444] TCP: Hash tables configured (established 2048 bind 2048)
[    0.308583] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.308642] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.309069] NET: Registered protocol family 1
[    0.312501] imx rpmsg driver is registered.
[    0.315185] Bus freq driver module loaded
[    0.317501] futex hash table entries: 256 (order: 2, 16384 bytes)
[    0.335591] VFS: Disk quotas dquot_6.6.0
[    0.336047] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.340341] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.342120] fuse init (API version 7.23)
[    0.353353] io scheduler noop registered
[    0.353400] io scheduler deadline registered
[    0.353939] io scheduler cfq registered (default)
[    0.354948] imx-weim 21b8000.weim: Driver registered.
[    0.359459] lumi_r supply power not found, using dummy regulator
[    0.361641] lumi_b supply power not found, using dummy regulator
[    0.363403] lumi_g supply power not found, using dummy regulator
[    0.365690] MIPI DSI driver module loaded
[    0.366128] MIPI DSI driver module loaded
[    0.371975] imx-sdma 20ec000.sdma: no event needs to be remapped
[    0.372192] imx-sdma 20ec000.sdma: loaded firmware 3.3
[    0.380134] imx-sdma 20ec000.sdma: initialized
[    0.382200] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 19, base_baud = 5000000) is a IMX
[    1.031479] console [ttymxc0] enabled
[    1.036987] 21e8000.serial: ttymxc1 at MMIO 0x21e8000 (irq = 217, base_baud = 5000000) is a IMX
[    1.082916] imx-rng 2284000.rngb: iMX RNG Registered.
[    1.088647] imx sema4 driver is registered.
[    1.093137] [drm] Initialized drm 1.1.0 20060810
[    1.099087] [drm] Initialized vivante 1.0.0 20120216 on minor 0
[    1.132009] brd: module loaded
[    1.148942] loop: module loaded
[    1.152913] pn54x_dev_init-->lumi
[    1.156431] pn54x_probe
[    1.158954] pn544 1-0028: FIRM GPIO <OPTIONAL> error getting from OF node
[    1.165947] pn544 1-0028: CLKREQ GPIO <OPTIONAL> error getting from OF node
[    1.173023] 1-0028 supply nxp,pn54x-pvdd not found, using dummy regulator
[    1.180046] 1-0028 supply nxp,pn54x-vbat not found, using dummy regulator
[    1.186995] 1-0028 supply nxp,pn54x-pmuvcc not found, using dummy regulator
[    1.194149] 1-0028 supply nxp,pn54x-sevdd not found, using dummy regulator
[    1.201200] pn54x_probe: request irq_gpio 7
[    1.205425] pn54x_probe: request ven_gpio 3
[    1.210118] pn54x_probe : requesting IRQ 35
[    1.229658] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xda
[    1.236150] nand: Macronix MX30LF2G18AC
[    1.240073] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.248353] gpmi-nand 1806000.gpmi-nand: mode:5 ,failed in set feature.
[    1.255896] Bad block table found at page 131008, version 0x01
[    1.262483] Bad block table found at page 130944, version 0x01
[    1.269161] 4 cmdlinepart partitions found on MTD device gpmi-nand
[    1.275446] Creating 4 MTD partitions on "gpmi-nand":
[    1.280588] 0x000000000000-0x000000300000 : "boot"
[    1.288031] 0x000000300000-0x000000a00000 : "kernel"
[    1.295535] 0x000000a00000-0x000000b00000 : "dtb"
[    1.302775] 0x000000b00000-0x000010000000 : "rootfs"
[    1.311214] gpmi-nand 1806000.gpmi-nand: driver registered.
[    1.323215] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.329914] ehci-mxc: Freescale On-Chip EHCI Host driver
[    1.335735] usbcore: registered new interface driver usb-storage
[    1.342036] usbcore: registered new interface driver usb_ehset_test
[    1.350994] 2184800.usbmisc supply vbus-wakeup not found, using dummy regulator
[    1.360151] 2184000.usb supply vbus not found, using dummy regulator
[    1.374606] mousedev: PS/2 mouse device common for all mice
[    1.382299] input: 20cc000.snvs:snvs-powerkey as /devices/platform/soc/2000000.aips-bus/20cc000.snvs/20cc000.snvs:snvs-powerkey/input/input0
[    1.400242] snvs_rtc 20cc000.snvs:snvs-rtc-lp: rtc core: registered 20cc000.snvs:snvs-r as rtc0
[    1.409273] i2c /dev entries driver
[    1.415694] IR NEC protocol handler initialized
[    1.420386] IR RC5(x/sz) protocol handler initialized
[    1.425488] IR RC6 protocol handler initialized
[    1.430111] IR JVC protocol handler initialized
[    1.434691] IR Sony protocol handler initialized
[    1.439350] IR SANYO protocol handler initialized
[    1.444140] IR Sharp protocol handler initialized
[    1.448894] IR MCE Keyboard/mouse protocol handler initialized
[    1.454818] IR XMP protocol handler initialized
[    1.465609] imx2-wdt 20bc000.wdog: use WDOG_B to reboot.
[    1.472000] imx2-wdt 20bc000.wdog: timeout 60 sec (nowayout=0)
[    1.479255] sdhci: Secure Digital Host Controller Interface driver
[    1.485601] sdhci: Copyright(c) Pierre Ossman
[    1.490065] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.497494] /soc/[email protected]/[email protected]: voltage-ranges unspecified
[    1.504784] sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
[    1.515399] sdhci-esdhc-imx 2190000.usdhc: No vmmc regulator found
[    1.521696] sdhci-esdhc-imx 2190000.usdhc: No vqmmc regulator found
[    1.570101] mmc0: SDHCI controller on 2190000.usdhc [2190000.usdhc] using ADMA
[    1.604260] usbcore: registered new interface driver usbhid
[    1.610221] usbhid: USB HID core driver
[    1.614882] vf610-adc 2198000.adc: Debug vf610_adc_proble()
[    1.621222] 2198000.adc supply vref not found, using dummy regulator
[    1.627901] vf610-adc 2198000.adc: Debug[0] channels[2]
[    1.642465] wm8524_i2c_probe:
[    1.650111] mmc0: new high speed SDIO card at address 0001
[    1.656555] wm8960 1-001a: Failed to issue reset
[    1.661617] wm8960: probe of 1-001a failed with error -5
[    1.670342] fsl-asrc 2034000.asrc: driver registered
[    1.683176] imx_wm8524_probe:
[    1.686870] wm8524_probe:
[    1.691043] imx-wm8524 sound2: wm8524-hifi <-> 2028000.sai mapping ok
[    1.698919] imx-wm8524 sound2: snd-soc-dummy-dai <-> 2034000.asrc mapping ok
[    1.706525] imx-wm8524 sound2: wm8524-hifi <-> 2028000.sai mapping ok
[    1.720258] NET: Registered protocol family 26
[    1.726888] NET: Registered protocol family 10
[    1.733666] sit: IPv6 over IPv4 tunneling driver
[    1.740371] NET: Registered protocol family 17
[    1.745191] Bluetooth: RFCOMM TTY layer initialized
[    1.750343] Bluetooth: RFCOMM socket layer initialized
[    1.755555] Bluetooth: RFCOMM ver 1.11
[    1.759374] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[    1.764785] Bluetooth: BNEP filters: protocol multicast
[    1.770108] Bluetooth: BNEP socket layer initialized
[    1.775122] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.781136] Bluetooth: HIDP socket layer initialized
[    1.786150] 8021q: 802.1Q VLAN Support v1.8
[    1.790461] lib80211: common routines for IEEE802.11 drivers
[    1.796431] Key type dns_resolver registered
[    1.802670] cpu cpu0: dev_pm_opp_get_opp_count: device OPP not found (-19)
[    1.837481] ubi0: attaching mtd3
[    3.119401] random: nonblocking pool is initialized
[    4.473470] ubi0: scanning is finished
[    4.513069] ubi0: attached mtd3 (name "rootfs", size 245 MiB)
[    4.518918] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    4.526529] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    4.533441] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    4.540568] ubi0: good PEBs: 1956, bad PEBs: 4, corrupted PEBs: 0
[    4.546693] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128
[    4.553997] ubi0: max/mean erase counter: 854/225, WL threshold: 4096, image sequence number: 1181536162
[    4.563554] ubi0: available PEBs: 0, total reserved PEBs: 1956, PEBs reserved for bad PEB handling: 36
[    4.572953] ubi0: background thread "ubi_bgt0d" started, PID 73
[    4.578964] dhd_module_init in
[    4.584224] input: regulators:gpio-keys as /devices/platform/regulators/regulators:gpio-keys/input/input1
[    4.594712] snvs_rtc 20cc000.snvs:snvs-rtc-lp: setting system clock to 1970-01-01 00:00:03 UTC (3)
[    4.626430] gpio_dvfs: disabling
[    4.629712] vref-3v3: disabling
[    4.632976] can-3v3: disabling
[    4.636405] ALSA device list:
[    4.639398]   #0: wm8524-audio
[    4.722328] UBIFS (ubi0:0): recovery needed
[    4.871443] UBIFS (ubi0:0): recovery deferred
[    4.876039] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "rootfs", R/O mode
[    4.884442] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    4.894439] UBIFS (ubi0:0): FS size: 241635328 bytes (230 MiB, 1903 LEBs), journal size 12062720 bytes (11 MiB, 95 LEBs)
[    4.905376] UBIFS (ubi0:0): reserved for root: 4952683 bytes (4836 KiB)
[    4.912172] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 5E2837F6-76F8-4DD0-A19B-F90839CD6F35, small LPT model
[    4.925383] VFS: Mounted root (ubifs filesystem) readonly on device 0:14.
[    4.935231] devtmpfs: mounted
[    4.939751] Freeing unused kernel memory: 540K (80aa1000 - 80b28000)
INIT: version 2.88 booting
Starting udev
[    7.336402] udevd[105]: starting version 3.1.5
[    7.998450] UBIFS (ubi0:0): completing deferred recovery
[    8.136502] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 129
[    8.154936] UBIFS (ubi0:0): deferred recovery completed
INIT: Entering runlevel: 5
Configuring network interfaces... eth0: ERROR while getting interface flags: No such device
Running local boot scripts (/etc/rc.local)[   11.651973] RTL871X: module init start
[   11.655773] RTL871X: rtl8189es v4.3.18.3_20185.20161116
[   11.665764] RTL871X: build time: Feb 27 2017 07:57:22
[   11.679391] RTL871X: CHIP TYPE: RTL8188E
[   11.683976] RTL871X: rtw_hal_config_rftype RF_Type is 3 TotalTxPath is 1
[   11.690934] RTL871X: Chip Version Info: CHIP_8188E_Normal_Chip_TSMC_D_CUT_1T1R_RomVer(0)
[   11.699206] RTL871X: EEPROM type is E-FUSE
[   11.703378] RTL871X: =>_CardEnable
[   11.713028] RTL871X: SetHwReg8188E: bMacPwrCtrlOn=1
[   11.717931] RTL871X: <=_CardEnable
[   11.721830] RTL871X: _ReadPROMContent: 9346CR=0x20, Boot from EFUSE, Autoload OK
[   11.729498] RTL871X: =>_InitPowerOn_8188ES
[   11.733662] RTL871X: =>_CardEnable
[   11.737084] RTL871X: =>_CardEnable bMacPwrCtrlOn == _TRUE do nothing !!
[   11.743741] RTL871X: <=_CardEnable
[   11.747512] RTL871X: <=_InitPowerOn_8188ES
[   11.751769] bFWReady == _FALSE call reset 8051...
[   11.756965] RTL871X: =====> _8051Reset88E(): 8051 reset success .
[   11.781772] RTL871X: efuse_read_phymap_from_txpktbuf bcnhead:0
[   11.788092] RTL871X: efuse_read_phymap_from_txpktbuf len:178, lenbak:178, aaa:178, aaabak:178
[   11.802752] RTL871X: efuse_read_phymap_from_txpktbuf read count:176
[   11.809230] RTL871X: EEPROM ID=0x8129
[   11.813012] RTL871X: Hal_ReadPowerSavingMode88E...bHWPwrPindetect(0)-bHWPowerdown(0) ,bSupportRemoteWakeup(0)
[   11.822983] RTL871X: ### PS params=>  power_mgnt(0),usbss_enable(0) ###
[   11.829616] RTL871X: ======= Path 0, Channel 1 =======
[   11.834860] RTL871X: Index24G_CCK_Base[0][1] = 0x25
[   11.839755] RTL871X: Index24G_BW40_Base[0][1] = 0x29
[   11.844769] RTL871X: ======= Path 0, Channel 2 =======
[   11.850012] RTL871X: Index24G_CCK_Base[0][2] = 0x25
[   11.854908] RTL871X: Index24G_BW40_Base[0][2] = 0x29
[   11.859925] RTL871X: ======= Path 0, Channel 3 =======
[   11.865078] RTL871X: Index24G_CCK_Base[0][3] = 0x25
[   11.870001] RTL871X: Index24G_BW40_Base[0][3] = 0x29
[   11.874978] RTL871X: ======= Path 0, Channel 4 =======
[   11.880160] RTL871X: Index24G_CCK_Base[0][4] = 0x25
[   11.885049] RTL871X: Index24G_BW40_Base[0][4] = 0x29
[   11.890052] RTL871X: ======= Path 0, Channel 5 =======
[   11.895203] RTL871X: Index24G_CCK_Base[0][5] = 0x25
[   11.900161] RTL871X: Index24G_BW40_Base[0][5] = 0x29
[   11.905140] RTL871X: ======= Path 0, Channel 6 =======
[   11.910330] RTL871X: Index24G_CCK_Base[0][6] = 0x27
[   11.915221] RTL871X: Index24G_BW40_Base[0][6] = 0x2b
[   11.920227] RTL871X: ======= Path 0, Channel 7 =======
[   11.925377] RTL871X: Index24G_CCK_Base[0][7] = 0x27
[   11.930301] RTL871X: Index24G_BW40_Base[0][7] = 0x2b
[   11.935276] RTL871X: ======= Path 0, Channel 8 =======
[   11.940455] RTL871X: Index24G_CCK_Base[0][8] = 0x27
[   11.945344] RTL871X: Index24G_BW40_Base[0][8] = 0x2b
[   11.950345] RTL871X: ======= Path 0, Channel 9 =======
[   11.955496] RTL871X: Index24G_CCK_Base[0][9] = 0x24
[   11.960408] RTL871X: Index24G_BW40_Base[0][9] = 0x28
[   11.965386] RTL871X: ======= Path 0, Channel 10 =======
[   11.970651] RTL871X: Index24G_CCK_Base[0][10] = 0x24
[   11.975628] RTL871X: Index24G_BW40_Base[0][10] = 0x28
[   11.980718] RTL871X: ======= Path 0, Channel 11 =======
[   11.985955] RTL871X: Index24G_CCK_Base[0][11] = 0x24
[   11.990996] RTL871X: Index24G_BW40_Base[0][11] = 0x28
[   11.996062] RTL871X: ======= Path 0, Channel 12 =======
[   12.001334] RTL871X: Index24G_CCK_Base[0][12] = 0x24
[   12.006311] RTL871X: Index24G_BW40_Base[0][12] = 0x28
[   12.011405] RTL871X: ======= Path 0, Channel 13 =======
[   12.016642] RTL871X: Index24G_CCK_Base[0][13] = 0x24
[   12.021653] RTL871X: Index24G_BW40_Base[0][13] = 0x28
[   12.026716] RTL871X: ======= Path 0, Channel 14 =======
[   12.031983] RTL871X: Index24G_CCK_Base[0][14] = 0x24
[   12.036959] RTL871X: Index24G_BW40_Base[0][14] = 0x28
[   12.042049] RTL871X: ======= TxCount 0 =======
[   12.046507] RTL871X: CCK_24G_Diff[0][0]= 0
[   12.050684] RTL871X: OFDM_24G_Diff[0][0]= 0
[   12.054885] RTL871X: BW20_24G_Diff[0][0]= -2
[   12.059165] RTL871X: BW40_24G_Diff[0][0]= 0
[   12.063393] RTL871X: EEPROMRegulatory = 0x0
[   12.067590] RTL871X: mlmepriv.ChannelPlan = 0x20
[   12.072248] RTL871X: CrystalCap: 0x39
[   12.075923] RTL871X: EEPROM Customer ID: 0x 0
[   12.080357] RTL871X: Board Type: 0x 0
[   12.084031] RTL871X: ThermalMeter = 0xf
[   12.087878] RTL871X: pHalData->EEPROMRFGainVal=0
[   12.092547] RTL871X: Hal_ReadRFGainOffset => EEPRORFGainOffset = 0x00,EEPROMRFGainVal=0x00,thermal_offset:0x00
[   12.102681] RTL871X: <==== ReadAdapterInfo8188ES in 380 ms
[   12.108407] RTL871X: Hal_ChannelPlanToRegulation ChannelPlan:0x20,Regulation(2_4G/5G):0x03,0x03
[   12.117176] RTL871X: init_channel_set ChannelPlan ID 20 Chan num:13
[   12.124658] RTL871X: rtw_alloc_macid((null)) if1, hwaddr:ff:ff:ff:ff:ff:ff macid:1
[   12.140222] RTL871X: rtw_macaddr_cfg mac addr:54:ef:44:c9:f6:9b
[   12.146287] RTL871X: bDriverStopped:True, bSurpriseRemoved:False, bup:0, hw_init_completed:0
[   12.154867] RTL871X: rtw_wiphy_alloc(phy0)
[   12.158983] RTL871X: rtw_wdev_alloc(padapter=90cef000)
[   12.164181] RTL871X: rtw_wiphy_register(phy0)
[   12.168553] RTL871X: Register RTW cfg80211 vendor cmd(0x67) interface
[   12.178706] RTL871X: rtw_ndev_init(wlan0) if1 mac_addr=54:ef:44:c9:f6:9b
[   12.211712] RTL871X: module init ret=0
==========================================
======== ^_^ start miot hkbridge =========
==========================================
fac_test bulid time:04:06:52 Oct 19 2018
gobal_cmd_list size 3204
Input cmd:

Taki coś mi wypluło...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

 

adblock-th.png

 

 

 

Our forum lives up to the advertisements displayed.
To browse the content of our forum, please disable AdBlock.

 

 

I accept